Accessories

- 50 hour service kit for Deluxe and Super Deluxe rear shocks - Includes air can seals, piston seal, and glide rings

Service kits include dust seals, foam rings, oil seals, air and damper o-rings needed for basic service.

Get accurate and precise results every time with RockShox's High-Pressure Digital Fork/Shock Pump. It features an aluminum barrel with an ergonomic handle, a handy finger-tap bleed adjust button for fine-tuning settings, and a large digital BAR/PSI readout. It runs off one CR2032 battery (included) and the hose swivels 360-degrees to fit anywhere.

RockShox, 11.4115.129.010, Service Kit, Monarch Plus (does not include air can seals)

Keep your Reverb dropper post performing at its best with RockShox's Reverb Hydraulic Fluid. It's optimized for the remotes of the Reverb as well as the Monarch XX rear shock.

Tools for repair and maintenance of RockShox Reverb suspension seatposts. - Specific to RockShox Reverb post

200 HOUR/1 YEAR SERVICE KIT (INCLUDES AIR CAN SEALS, PISTON SEAL, GLIDE RINGS, IFP SEALS, SEAL GREASE/OIL) - SUPER DELUXE THRUSHAFT C1 - TREK (2021)

200 hour/1 year Service Kit (includes sealhead seals, piston seal, glide rings, IFP seals, grease) - Super Deluxe Coil (2018+)

RockShox's Suspension Oil comes in different weights to match the most popular suspension fork and shock setups.

- Trek Reaktiv Thru Shaft 200 hour service kit

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

The smartest, most convenient torque key now comes with enough bits to suit every need. Make sure those stem bolts are tight enough, and double check the torque on the seatpost bolt while you're at it. The Ritchey Bicycle Torque Key is an essential tool for those important bolts. Available with 4 or 5Nm options, this 6-bit set includes just about every bit you'll need for your bike, and a convenient holder to keep it all organized. - Hex 3/4/5mm - Torx T-20/25 - Phillips #1 - 4 or 5Nm max torque - Bit holder included

Somewhere between the excitement of competition and recovery, it can be easy to misplace things. With Profile's Aerodrink Parts Kit you can replace both straws, the mesh sponge and the two rubber bands that keep your Aerodrink ready for your next event.

Profile Design's UCM XL Universal Computer Mount provides a convenient 60mm-long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.

- Exceptional friction reduction and anti-wear properties with greatly reduced friction in metal to metal applications

ProGold ProLink is designed to shed dirt, mud, and abrasives, and reduce tacky build-up in all climates. - Smoother shifting, quieter drive train - Repels moisture and reduces oxidation and corrosion - Disperses water and resists wash-off - Will not build up or get tacky - Works well in all climates - Longer chain and sprocket life - Long-lasting - Can be used as a dry lubricant - Environmentally friendly - Available in: 4 fluid-ounce drip, 8 fluid-ounce aerosol, 16 fluid-ounce pump, and 32 fluid-ounce.

- Xtreme chain lube is formulated for long-distance and extreme off-road conditions - MFR bonds to metal surfaces and resists build-Up and tackiness, in addition to shedding water

Planet Bike's Dial Gauge makes it easy to ensure you always have the right pressure in your tires, which makes the riding easy and helps prevent flats. Built to last, this quality gauge works on all valves and has a large easy-to-read dial.

The Protege 9.0 uses the Planet Bike 4-line MacroMonitor display and has digital wireless technology to eliminate messy wires. - Functions: Current Speed - Speed Comparator - Ride Time - Trip Distance - Dual Odometer (for 2 wheel sizes) - Average Speed - Maximum Speed - Clock - Temperature - Digital technology results in decreased interference - Easy-to-adjust sensor that fits bladed spokes up to 4 mm - 4-Line MacroMonitor LCD displays up to 5 pieces of data at a glance - Fits 25.0-31.8mm handlebars - 21" wireless range

The tire lever, though seemingly one of the simplest and most basic of cycling tools, is one commonly used by almost every cyclist, and unfortunately, one often responsible for unnecessary frustration. Really, what is more fun than flatting far away from home, being thrilled you lugged that spare tube and pump, and then having your tire levers snap in two? Pedro's award-winning, universally loved tire levers feature molded box construction and a proprietary plastic composite blend that makes them the strongest levers available. The unique chisel tip shape easily inserts beneath the tire bead and the slightly thicker shape keeps the lever securely in place. Additionally, the bold shape of the lever and helpful dual spoke hooks makes removal of even the tightest tires a simple task. - Award-winning and universally loved - Molded box construction and proprietary plastic blend makes these the strongest levers available - Chisel tip shape is easy to insert beneath the bead and the slightly thicker shape keeps the tire lever from slipping - Bold shape makes it easy to remove the tightest of tires without bending or breaking

Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-1 FEATURES - 4mm, 5mm, and 6mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit

Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-3 FEATURES - 2mm, 2.5mm, and 3mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit

Removes and installs crank caps on Shimano® Hollowtech II® cranks. Includes built in hook to lift the safety plate, speeding crank removal. Steel, investment cast body provides good leverage and includes an option to use with an 8mm hex wrench for removing seized caps.

The BBT-22 is a shop-quality tool for installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-22 ensures maximum engagement with the bottom bracket cup. It can be used with a 3/8-inch drive torque wrench, a 3/8-inch ratchet driver, a 32mm wrench, the Park FRW-1 Freewheel Remover Wrench (sold separately), or a 1-inch wrench.

Park's BBT-32 is the perfect solution for the home mechanic installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-32 utilizes a flat tooth profile to ensure maximum engagement with the bottom bracket cup and features 32mm wrench flats.

Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.

The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.

Park's Bottom Bracket/Cassette Tool for Campagnolo is an indispensable tool for your Campagnolo drivetrain. It's for installing and removing all Record, Chorus, Centaur and Athena bottom brackets, and all Campagnolo cassette lockrings.

A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

Heat treated alloy tool steel, one inch base fits wrench or bench vise. Thin wall construction allows use without removal of cones and locknuts. The FR-5.2G has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, SunRace, SunTour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also Fits Shimano disc brake lockrings - Guide pin stabilizes tool

A worn chain shifts poorly and wears sprockets at an accelerated rate. Park Tool's Chain-Wear Indicator is a “go-no go” gauge designed to accurately indicate when a chain reaches .5% and .75%, the points at which most chain manufacturers suggest replacement. The updated CC-3.2 is longer, more accurate and features permanent measurement markings.

Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)

A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.

Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.

A handy tool designed to make installation and removal of bicycle electronic shifting wires and batteries quick and easy. - Durable composite body is durable and prevents scratching of expensive components - Angled Shimano Di2 E-TUBE ends allow for both installation and removal in tight spaces - Universal coin cell tool helps remove and install battery covers on SRAM eTap

There’s no easier or more effective way to patch a cut tire on the road or trail than carrying and using Park Emergency Tire Boots (3 per package). These thin, extra-tough patches peel and stick to the insides of tires to repair cuts and contain the tube until you can replace the tire.

The Park FR-2 Freewheel Remover fits SunTour two-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel. (Not recommended for use with SunTour 4- and 6-notch freewheels.)

The Park FR-3 Freewheel Remover fits SunTour four-notch freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

The Park FR-6 Freewheel Remover fits most 4-notch BMX and singlespeed freewheels. It can be held with a wrench or vise and its narrow profile allows use without removal of cones and locknuts.

The Park FR-7 Freewheel Remover fits Falcon freewheels. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.

Park's FR-8 Freewheel Remover fits flip-flop BMX hubs with 30 x 1mm threads. It can be held with a wrench or vise, and its narrow profile allows use without removal of cones and locknuts.

12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.

Park's Hex Wrenches are every mechanic's best friend. They are constructed from industrial quality steel for durability and feature chamfered tips for a precision fit. And, their convenient L shape is perfect for jobs that require lots of leverage or for getting to hard-to-reach bolts.

Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.

Park's Hydraulic Brake Piston Press is used to set or reset the piston(s) inside hydraulic disc brake calipers during installation, maintenance and repair. Just push it into the caliper to wedge the piston into place. It's made of tough tool steel with a comfortable and oversize rubber handle for a great grip.

The I-Beam Mini Fold-Up Set includes 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen and regular screwdriver. It's the perfect mini-tool to get you out of binds or make quick adjustments. And, it conveniently tucks into a pocket or pack.

The strong, lightweight IB-2 features ten essential tools in the compact form factor of our unique I-Beam handle. Perfect for on-the-ride adjustment of brakes, handlebars, saddles, or derailleurs. With its compact size, the IB-2 is a perfect tool for the saddlebag, jersey pocket, or toolbox.

Many chains use a master link that allows the chain to be installed and removed by hand. While master links don't require traditional chain tools, over time, dirt and corrosion can make it difficult to separate them by hand. Park's Master Link Pliers make removing and installing these master links quick and easy. Simply insert the specially sized jaws into the link and squeeze the vinyl-coated handles!

Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

Made from tough steel and reinforced with extra material at the highly stressed wrench openings, Park’s shop-quality Pedal Wrench is built to easily install and remove pedals, and to last and last. It has 15mm and 9/16-inch precision openings to fit all pedals. And it boasts a long, round, vinyl-coated handle that won’t dig into your hand and provides optimum leverage. There's even a hole in the end of the wrench for hanging it on your toolboard.

Park's PolyLube is specifically formulated to protect bearing components. Its Polyurea grease has extremely high shear strength to protect bottom brackets, headsets, pedals and hubs. Use it on threads, seatposts, stems and cables, too. It's also safe for fork seals, and repels water.

Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

If you have a bike with disc brakes, you'll want Park's Rotor Truing Fork. It allows you to gently adjust bent and damaged disc-brake rotors. It's made from high-quality steel and features 2 laser-cut slots for precise adjustments and a vinyl handle for comfort and control.

Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's professional-quality, precision-sized spoke wrenches are hardened and chrome plated for long service. Wrenches are vinyl coated in one of four colors indicating the size at a glance. You will find these wrenches in virtually every professional bike shop and every shop mechanic's personal tool stash. Make sure you have the sizes you need in your home toolbox and bike bag.

• Oversized hook for large MTB tires and tall aero rims • Inside width of 75mm (2.95") and 150mm (5.9") tall inside the J-bend • Made from 9.5mm wire • Wood screw thread is nominally 11.4mm outside diameter (15/32") with 7 threads per inch • Use a minimum of 11/32" drill size to pilot wood hole • Blue vinyl coated

• Park Tool Storage Hooks are perfect for hanging bikes, wheels, etc. • Vinyl coated to prevent scratching. • Wood threaded • Made from 7mm steel rod • For a pilot hole in wood, use a 1/4" or 6mm bit • Sold in pairs